Turbidity Meters Singapore — NTU, FNU and ISO 7027 Measurement

Published: {{NEW_ARTICLE_DATE}}  |  By JWRESEARCH  |  Category: Water Quality Instruments

Turbidity is the water quality parameter most often measured and most often measured badly. The instrument is simple, but the number depends on optical geometry, wavelength, calibration standard and cell condition. Two compliant meters can legitimately disagree on the same sample.

JW RESEARCH SUPPLY supplies portable and benchtop turbidity meters, low-range nephelometers, inline sensors and calibration standards to water plants, environmental laboratories, food producers and research institutes in Singapore. This guide covers what the reading means and how to keep results comparable.

What a Turbidimeter Measures

A turbidimeter shines light into a sample and measures the light scattered by suspended particles, usually at 90 degrees. More particles, or larger ones, scatter more light. Because scattering depends on particle size, shape and refractive index as well as concentration, turbidity is not a mass concentration and cannot be converted to milligrams per litre without a site-specific correlation.

Nephelometry, the 90 degree measurement, is the reference approach for drinking water because it tracks the fine particles that shield micro-organisms from disinfection. Transmission and backscatter designs suit higher ranges and inline process control, where the question is trend rather than compliance.

Methods and Units

USEPA method 180.1 specifies a tungsten lamp and a 90 degree detector, reporting in NTU. ISO 7027 specifies an 860 nm infrared source, which reduces colour interference, reporting in FNU. Neither supersedes the other; for regulatory work follow the method your authority cites and state it on the report.

Ratio turbidimetry uses a second detector, usually forward scatter, to compensate for colour and lamp ageing, which makes it the practical choice for low-range work in coloured matrices.

Typical Specifications

Type Range Resolution Light Source / Method Best For
Portable field nephelometer 0 – 1,000 NTU 0.01 NTU below 100 Tungsten or LED, 90° Site checks, distribution sampling
Benchtop ratio turbidimeter 0 – 4,000 NTU 0.01 NTU below 100 LED 860 nm, ratio Drinking water compliance, QC
Low-range drinking water meter 0 – 20 NTU 0.001 NTU 860 nm, 90° scatter Final treated water, validation
Wastewater / process meter 0 – 4,000 NTU or g/L 1 NTU or 0.01 g/L Backscatter or transmission Aeration tanks, effluent, slurries
Inline sensor 0 – 4,000 NTU 0.01 NTU at low range 860 nm, 90° or backscatter Continuous process and alarm control

Consumables and Accessories

Item Function Practical Note
Sample cells, indexed Fixed optical position for repeatability Always insert at the marked orientation
Formazin stock and dilutions Primary calibration standard Prepare fresh; suspensions settle within hours
Stabilised polymer standards Convenient secondary checks Use within the certified expiry; store upright
Silicone oil and lens tissue Masks cell scratches and fingerprints A thin film, wiped in one direction only
Cell cleaning solution Removes biofilm and residue Rinse with deionised water, air dry upside down
Degassing syringe or kit Removes bubbles from cold samples Let samples stand; never shake before reading

Sources of Error Worth Knowing

Bubbles are the leading cause of impossible readings. Cold samples hold dissolved gas that forms tiny bubbles on the cell wall, each scattering like a particle. Let the sample stand, or degas gently, and never shake it before measuring.

Cell condition comes second. A fingerprint can add several NTU at low range, and scratches add an offset calibration cannot remove. Keep dedicated cells for standards and samples, handle them by the frosted faces and check them against a blank periodically.

Sample representativeness is the third. Turbidity settles, so a grab sample left standing reads lower at the bottom and higher at the top. Measure soon after collection, invert gently and record the elapsed time. Particle size matters too: coarse silt and fine clay at the same mass concentration give very different NTU values.

Singapore Conditions and Daily Practice

High humidity condenses on cells taken from cold storage, so equilibrate samples before reading. Residual chlorine bleaches formazin standards, so use fresh standards stored away from light and heat.

For PUB-related drinking water work, low-range performance and documented calibration matter more than a wide measuring range. For used water and effluent, a process meter with bubble rejection and a defined cleaning interval serves better than a laboratory instrument pushed beyond its design range.

Calibration and Verification

Build a calibration across the working range, not at one point: a single check catches offset but not slope error. Use fresh formazin dilutions or certified standards, and let each reach room temperature and clear of bubbles before reading.

Verify daily with a check standard and record the value, standard lot and cell used. A slow upward drift usually means a dirty cell or a fading lamp, both cheaper to fix than a failed audit. After service or a lamp change, repeat the full calibration before returning the meter to compliance work.

Frequently Asked Questions

What is the difference between NTU, FNU and EBC?
NTU comes from formazin-calibrated nephelometry, typically EPA 180.1 with a tungsten lamp; FNU comes from ISO 7027 with an 860 nm infrared source; EBC is the brewery unit, roughly 1 EBC equals 4 NTU. Report the unit with the method.

Which meter suits low-range drinking water testing?
A ratio benchtop or low-range portable with 0.01 NTU resolution, stated accuracy of about plus or minus 2 percent plus 0.01 NTU, and a sealed indexed cell. Range beyond 100 NTU is largely unused in treated water.

How often should a turbidity meter be calibrated?
Full multi-point calibration at a defined interval and after service or a lamp change, plus a single check standard daily or before each batch.

Does JWRESEARCH supply turbidity meters in Singapore?
Yes — portable and benchtop nephelometers, low-range drinking water meters, process and inline sensors, sample cells, formazin and polymer standards, and cleaning accessories, with local advice and delivery.

Ordering Checklist

Tell us the method, matrix and reporting limit, and we will propose a meter, cells and calibration package suited to how you actually sample.

Contact JWRESEARCH

JW RESEARCH SUPPLY — laboratory equipment and consumables, Singapore.
Telephone / WhatsApp: +65 8039 3660
Email: SINGAPORE@JWSHY.COM
Website: www.jwresearch.cn